It's a Great DayMain Water Shut Off Valve
Every homeowner should locate their main water shut off valve and know how to use it.
There are two types of main water valves: the gate valve and the ball valve. The gate valve is recognized by its round handle that must be turned a number of times to open or close the valve. The ball valve is recognized by its single handle that needs to be turned ¼ turn or 90 degrees, to turn the water on or off.
Your plumbing professional can tell you about the condition of the main water valve in your home and replace it if necessary.
Water Damage Prevention
Water-related damage causes millions of dollars of losses each year. A sampling of 63 percent of Washington home insurers found that water-related losses totaled $1.7 billion between 1997 and 2001. Based on the survey data, the average cost of a water claim in 2001 was $4730, up from $2537 in 1997, nearly doubling the average cost of a water claim in four years. The Plumbing Guys are happy to provide this information as a service to you.
Why Plumbing Maintenance is Important
Homeowner’s insurance generally covers household water damage if the damage is sudden and accidental, such as damage caused by burst pipes. It does not cover damage of the sort covered by flood insurance, i.e., rising water from outside; or damage caused over time by lack of maintenance.
A water damage claim can be a red flag to insurers as well as to future homebuyers, signaling a likelihood of repeat water claims. It is better to maintain a home for water issues than face the risks of increased insurance costs and reduced home marketability.
Identifying Water Problems
Look at your water bill. By comparing monthly usage figures, you may get tipped off to a small leak before it becomes a big problem. Major, unexplained fluctuations in your water bill are often a sign of water leaks.
Use a water pressure gauge to determine whether your household water pressure is set too high. The ideal household water pressure is 60-80 pounds per square inch. (psi), but many homes are set at 100 or higher. Attach the gauge to an outdoor faucet and turn the water on full to determine water pressure.
Preventative Maintenance
Know where your water shutoff valve is located and be sure that the entire family knows how to shut off household water supplies in the event of a sudden pipe or hose break.
Inspect your plumbing annually. Just as you change the batteries in your smoke detectors each year, you should inspect your water pipes and fittings annually. This is a simple check that takes minutes, and could prevent thousands of dollars in water damage.
Inspect around your water heater, washer, dishwasher, sinks, lavatories and refrigerator icemaker. If hoses indicate wear, replace them. Consider replacing hoses to major appliances such as your washer and dishwasher every two to five years. Steel, so-called “no burst” hoses have been shown to have a longer lifespan than other models.
When you go on vacation, turn off the water to your washer while you’re out of town. Many homeowners have returned from vacation to find their washer hoses have burst, flooding their homes.
Never leave the house with appliances, such as dishwashers, washers or dryers, still operating.
Let faucets connected to vulnerable pipes drip during extremely cold weather. This keeps the water moving and helps to reduce the chance of freezing.
If your bathroom has an exhaust fan, be sure to run it while the shower is on. This helps to remove steam from the room.
Water Pressure
The Uniform Plumbing Code (UPC) calls for water to be delivered to homes for domestic use at between 35 and 80 psi. Angle stops (valves) and supply lines as well as appliances are designed to withstand up to 80 pounds per square inch.
Water pressure regulators take the water as it is delivered by the water district, and regulate it to between 50 and 70 psi. The pieces in the water pressure regulator that reduce the water pressure are made of rubber and metal. Over a period of time, they can fail. When the water pressure regulator fails, water pressure to the home is allowed to increase. This puts a strain on valves, hoses and appliances that they were not designed to withstand. Unchecked, excessive water pressure may cause a rupture in the supply lines or valves.
A water pressure test gauge can inform the homeowner if water pressure is excessive. Simply connect the gauge to an outdoor faucet, and turn on the water to determine the water pressure. Make sure the faucet used is “regulated”. Some outdoor faucets are unregulated. If the pipe connected to the faucet comes out of the wall, there is a fairly good chance that faucet is regulated. If the pressure exceeds 80psi, then there is either a failed pressure reducing vale on the system or no device at all. In either case, you should contact a licensed plumber to remedy this situation as excessive pressure besides being a code violation, will damage supply lines, hoses and faucets.
Generally speaking, replacing the water pressure regulator, including parts and labor, should cost less than a homeowner’s standard $500 deductible. A working water pressure regulator reduces the strain on plumbing fixtures and increases their service life.
Angle Stops
Angle stops are valves located under your kitchen and bathroom sinks, at your washing machine, at the toilet, and refrigerator icemaker. There are angle stops for both hot and cold water. Most angle stops are of the gate variety and are made of materials that may fail over time. Replacement of theses valves is recommended when they are showing signs of leaking or they have “frozen” in the open position – meaning they can’t be turned one way or the other. A plumbing professional may be able to change out old angle stops with a new ball variety in a modest size home for less than $1,500.
Angle stops need to be “exercised” regularly to make sure they are not frozen in the open position. Every month or two simply turn the angle stops off and on a few times. This will keep them working as they were designed. Never force a valve that is frozen in position. Consult a plumbing professional as soon as possible.
Water Supply Lines
Water supply lines are connected from the angle stop to the appliance they serve, such as a faucet, toilet, washing machine, dishwasher and icemakers. Many times these are thin rigid lines that can easily break and cause extensive damage. Water supply lines should be checked regularly for corrosion and rust and changed every 5 to 7 years.
Among the preferred lines are those that are stainless steel braided over rubber with threaded couplings on both ends for the sink and toilet lines. Don’t forget the dishwasher and refrigerator icemaker supply lines. They are often overlooked because they are hidden. Replace plastic tubing with either soft copper or steel braided supply lines.